Anritsu/MP1220A/ATM质量分析仪

• Anritsu/MP1220A/ATM质量分析仪
• 欲购买或租赁Anritsu/MP1220A/ATM质量分析仪？请在线咨询或拔打24小时电话：13715327187

详细资料：

特点 ·支持各种接口[1.5 Mbps (T1) - 622 Mbps (STM-4C/Oc-12c)] ·150Mbps直到CPCS面的实时分析 ·上/下游二路同时测量 ·1023路网络通道自动监测 ·采用ITU-TO.191标准信号 ·体积小、重量轻、便于携带 技术指标 ·MP1220A ATM Quality Analyzer Display 10.4 inch TFT color LCD with touch panel(analog resistive membrane) Memory storage 3.5 inch floppy disk drive(1.44 MP/720KB)andhard disk drive(≥500MB) Buzzer Alam,error External interface RS-232C(D-sub 9-pin),printer(Centronics,D-sub,25-pin),keyboard(PS/2mini-DIN 6-pin),mouse(PS/2,mini-DIN,+-pin)VGA(analog RGB,D-sub,15-pin) Slots 6(two channelmax.) EMC EN55011:1991,Group 1, Class A EN50082-1:1992 Harmonic current emissions;EN61000-3-2:1995,Class D Safety EN61010-1:1993(Installation Category Ⅱ PollutionDegree Ⅱ) Dimensions and mass 284(W)*221.5(H)*365(D)mm(≤12kg(exchudingunits) Power supply 100 to 120/200 to 240Vac(autoswitching),50to 60Hz≤300VA Operating range Operating:5° to 50℃(exluding FDD),Storage:-20°to 60℃ ·MU120001A STM-4/OC-12 Unit Bit rate 51.84,155.52,622.08Mbps Frames SDH/SONET Output signal Connector:FC(replaceable),1.31μm band(SM) Clock:Internal(±10ppm) external ereceive Level:-15 to -8dBm Code:NRZ Optical safety:IEC825-1 Class 1,21CFR1040.10 Class I Input signal Connector:FC(replaceable),1.31μm band(SM) Clock:Internal:±100ppm Level:-34 to -8 dBm(51.84Mbps,155.52Mbps),-28 to -8dBm(622.08Mbps) Code:NRZ Functions SOH/POH setting,SOH/POH monitoring,pathtrace empty cell setting cell scramble(de-scramble)on/off coset on/off HECerror correction on/off Error addition:Bit,B1,B2,B3,FEBE-L,FEBE-P,cell Alarm addition:LOS LOF AIS-L RDI-L AIS-P RDI-P LCD Error measrement :B1,B2,B3,MS-REI(FEBE-L),HP-REI(FEBE-P)HEC corrected cells,HECuncorrected cells Alarm measurement:LOS OOF LOF MS-AIS(AIS-L),MS-RDI)RDI-L)AU-AIS)AIS-O)HP-RDI(RDI-P)AU-LOP(LOP-P),LCD Pointers:Monitor, ±justification,NDF Auxilary output:Receive clock output tringger output. ·MU120002A STM-1/OC-3 Unit Bit rate 155.52Mbps Frames SDH/SONET Output signal Connector Optical:SC1.31μm(SM);Electrical:BNC 75Ω Clock:Internal( ±10ppm),external recive Optical level:-15 to -8dBm Electrical level:1±0.1Vp-p(CM) Code Cptical:MRZ Electrical:CMI Optical safety:IEC825-1 Class 1, 21CFR1040.10 Class I Input signal Connector Optical:SC 1.31μm(SM/MM);Electrical:BNC 75Ω Frequency range:±100ppm Optical level:-28 to -8dBm(SM) Electrical level:1±0.1Vp-p(CMI)*Cable loss:0 to 12dB,Monitor:20dB attenuatedlevel of above level can be applied Code Optical :NRZ;Electrical:CMI Functions SOH/POH setting,SOH/POH monitoring pathtrace empty cell setting cell scramble (de-scramble)on/off coset on/offHEC error correction on/off Error addition:Bit,B1,B2,B3,FEBE-L FEBE-P cell Alarm addition:LOS LOF AIS-L RDI-L AIS-P RDI-P LCD Error measrement :B1,B2,B3,MS-REI(FEBE-L),HP-REI(FEBE-P)HEC corrected cells,HECuncorrected cells Alarm measurement:LOS OOF LOF MS-AIS(AIS-L),MS-RDI)RDI-L)AU-AIS)AIS-O)HP-RDI(RDI-P)AU-LOP(LOP-P),LCD Pointers:Monitor, ±justification,NDF Auxilary output:Receive clock output tringger output. ·MU120010A T1/T3 Unit Bit rate 1.544Mbps(T1),44.736Mbps(T3) Frames 1.5M ESF(PLCP:on/off),45M C-bit parity(PLCP:on/off),45MM23(PLCP:on/off) Output signal Connector BNC:75Ω unbalanced(T3)8-pin modular:100Ω balanced(ISO/IEC 10173,T1) Clock :Internal(±10ppm) external receive Level :2.4 to 3.6 Vo-p(T1),0.36 to 0.85Vo-p (T3) Code T1:B8ZS,T3:B3ZS Input signal Connector BNC:75Ω unbalanced(T3)8-pin modular:100Ω balanced(ISO/IEC 10173,T1 Frequency range:±130ppm(T1),±20ppm(T3) Level:2.4 to 3.6Vo-p(T1),0.36 to 0.85 Vo-p(T3)*Monitor:20dB attenuatiedlefel of above level can be applied Code T1:B8ZS,T3:B3ZS Functions Empty cell setting,cell scramble(de-scramble)on/offcoset on/off HEC error correction on/off Error addition:Bit FEBE PLCP-BIP-8,PLCP-FEBE,cell Alarm addition:LOF LOS AIS yellow idle PLCP-LOF PLCP-yellow LCD Error measurement:Code CP FEBE CRC6 PLCP0BIP-8 PLCP-FEBE HEC corrected cellsHEC uncorrected cells Alarm measurement:LOS OOF AIS yellow idle PLCP-OOF PLCP-yellow LCD Auxiliary output:Receive clock output trigger output ·MU120011A E1/E3/E4 Unit Bit rate 2.048Mbps(E1),34.368Mbps(E3),139.264Mbps(E4) Frames 2M-CRC-4 off (PLCP:on/off),2M CRC4 on(PLCP:on/off),34MG.751(PLCP:on),34M GH.832(PLCP:off),139M G.832(PLCP:off) Output signal Connector D-sub(9-pin):120Ω balanced(E1)BNC:75Ω unbalanced(E1/E3/E4) Clock:Internal(±10ppm)external receive Level:3±0.3Vo-p(E1 balanced),2.37±0.237Vo-p(E1 unbalanced),1±0.1Vo-p (E3)1±0.1Vo-p (E4) Code E1/E3:HDB3,E4:CMI Input signal Connector D-sub(9-pin): 120Ω balanced(E1)BNC:75Ω unbalanced(E1/E3/E4) Frequency range:±100ppm(E1/E4),±20ppm(E3) Level:3±0.3Vo-p(E1 balanced),2.37±0.237Vo-p(E1 unbalanced),1±0.1Vo-p (E3)1±0.1Vo-p (E4) *Cable loss:0 to 5dB(E1),0 to 12dB(E3,E4)Monitor:20dB attenuatied levelof above level can be applied. Code E1/E3:HDB3,E4:CMI Functions Empty cell setting,cell scramble(de-scramble)on/offcoset on/off HEC error correction on/off Error addition:Bit FEBE PLCP-BIP-8,PLCP-FEBE,cell Alarm addition:LOF LOS AIS yellow idle PLCP-LOF PLCP-yellow LCD Error measurement:CRC4,code,BIP-8 REI PLCP-BIP-8 PLCP-FEBE HEC correctedcells HEC uncorrected cells Alarm measurement:LOS OOF AIS yellow idle PLCP-OOF PLCP-yellow LCD Auxiliary output:Receive clock output trigger output ·MU120012A E1/E3 Unit Bit rate 2.048Mbps(E1),34.368Mbps(E3) Frames 2M-CRC-4 off (PLCP:on/off),2M CRC4 on(PLCP:on/off),34MG.751(PLCP:on),34M GH.832(PLCP:off),34M G.832(PLCP:off) Output signal Connector D-sub(9-pin):120Ω balanced(E1)BNC:75Ω unbalanced(E1/E3) Level:3±0.3Vo-p(E1 balanced),2.37±0.237Vo-p(E1 unbalanced),1±0.1Vo-p (E3) Code:HDB3 Input signal Connector D-sub(9-pin):120Ω balanced(E1)BNC:75Ω unbalanced(E1/E3) Frequency range:±100ppm(E1),±20ppm(E3) Level:3±0.3Vo-p(E1 balanced),2.37±0.237Vo-p(E1 unbalanced),1±0.1Vo-p (E3) *Cable loss:0 to 6dB(E1),0 to 12dB(E3),Monitor:20dB attenuated levle ofabove level can be applied Code:HDB3 Functions Empty cell setting,cell scramble(de-scramble)on/offcoset on/off HEC error correction on/off Error addition:Bit FEBE PLCP-BIP-8,PLCP-FEBE,cell Alarm addition:LOF LOS AIS yellow idle PLCP-LOF PLCP-yellow LCD Error measurement:CRC4,code,BIP-8 REI PLCP-BIP-8 PLCP-FEBE HEC correctedcells HEC uncorrected cells Alarm measurement:LOS OOF AIS yellow idle PLCP-OOF PLCP-yellow LCD Auxiliary output:Receive clock output trigger output ·MU120015 ATM25M Unit Bit rate 32.00Mbps(25M) Output signal Connector:8-pin modular jack,100Ω(RJ45) Clock:Internal(±10ppm),external receive Level:2.7 to 3.4Vp-p (1 symbol) Code:NRZI(4B/5B) Input signal Connector:8-pin modular jack 100Ω(RJ45) Frequency: ±100ppm Level:2.7 to 3.4Vp-p (1 symbol) Code: NRZI(4B/5B) Functions Empty cell setting cell sramble(de-scramble)on/offcoset on/off HEC error correction on/off Error addition:Bit CRC5 cell Alarm adition:LOS AIS RAI LOF LCD Error measurement :CRC5,HEC corrected cell,HEC uncorrected cell Alarm measurement:LOS AIS RAI LOF LCD Auxiliary output:Receive clockoutput trigger output ·MU120016A 6.3M Unit Bit rate 6.312 Mbps(6.3M) Output signal Connector:BNC 75Ω Clock:Internal(±10ppm),external receive Level:2 ±0.3Vo-p Code:B8ZS Input signal Connector:BNC 75Ω Frequency: ±30ppm Level: 2 ±0.3Vo-p *Cable loss:0 to 6dB,Monitor:20dB attenuated level of above level can beapplied. Code:B8ZS Functions Empty cell setting cell scramble (de-scramble)on/offcoset on/off HEC error correction on/off Error addition:Bit CRC5 cell Alarm addtion:LOS AIS RAI LOF LCD Error measurement:CRC5 HEC corrected cell HEC uncorrected cell Alarm measurement:LOS AIS RAI LOF LCD Auxilary output:Receive clock output trigger output ·MU120017A 6.3/25M Unit Bit rate 6.312 Mbps(6.3M),32.00 Mbps(25M) Output signal Connector:8-pin modular jack,100Ω(RJ45 25M) Clock:Internal(±10ppm),external receive Level: 2 ±0.3Vo-p,2.7 to 3.4Vp-p (1 symbol) Code: 6.3M:B8ZS,25M:NRZI(4B/5B) Input signal Connector: BNC 75Ω(6.3M),8-pin modular jack 100Ω(RJ45,25M) Frequency range:±30ppm(6.3M),±100ppm(25M) Level: 2 ±0.3Vo-p,2.7 to 3.4Vp-p (1 symbol) * Cable loss:0 to 6dB,Monitor:20dB attenuated level of above level can beapplied. Code: 6.3M:B8ZS,25M:NRZI(4B/5B) Functions Empty cell setting cell scramble(de-scramble)on/off(6.3M only)coset on/off HEC error correction on/of(6.3M only),sync eventsend (25M only) Error addition 6.3M:Bit CRC5,cell 25M:LOS Alarm additon 6.3M:LOS AIS RAI LOF LCD 25M:LOS Error measurement 6.3M:CRC5 HEC corrected cell HEC uncorrected cell 25M:Code,HEC uncorrected cel illegal cell Alarm measurement 6.3M:LOS AIS RAI LOF LCD 25M：LOS Syny event (25M only):Send measure Auxiliary output:Receive clock output trigger output ·MU120020A QoS Unit Foreground cells(test cells) 0.191 externded 0.191 OAM test cell(PRBS15) null AAL1, AAL3/4(For null AAL1,AAL3/4,next pattern settable to payload PRBS9,PRBS 15,PRBS 15(non-inverted)PRBS 23,time stampprogrammable Cell generation timing CBR burst sawtooth waveform CBR with CDVPoisson distribution manual external edge external level detailed CBR burstfor UPC measurement programmable Background cell CBR(10 types) OAM cell AIS PDI,continuity check loopback programmableforward monitoring backward reporting backward reporting PM activetion/deactivation,CCactivation/deactivation Capture Capacity:4095 cells Filter:All cells specified cells header+first byte of payload match/mismatchcells Trigger:Manual,OAM cell receive cell error detect cell loww error detectcell loss detect cell misinsertion detect cell tagging external inputsignaletc. Display:Hexadecimal,ASCII cell interval translate Single-channel Error addition:Cell loss cell error Error detection:Bit errror error cell cell loss cell misnsertion non-conformingcell etc(measurement itme differ according to test cell) Alarm detection:VP-AIS,VP-RDI,VP-LOC,VC-AIS,VC-RDI,VC-LOC Others Bandwidth total cells cell delay measurement 1 point CDV measurement 2 pointCDV measurement cell interval measurement 1023 channel measureemnt(live monitor) Detect and measure 1023 channels on line Measurement items:Total cell count,CLP=0 cell count ,CLP=1 count OAM cellcount Auxiliary input Trigger input ·MU120021A Protocol Unit Send/receive memory 8MB(≥130,000 cells send:8MB receive:8MBsend+receive:4+4MB selectable) Cell send Transmit from memory according to time stamp.Able to transmit in every 1 cell. Able to edit AAL1 AAL3/4 AAL5 frame Capture Capacity:≥13,000 cells(at 8 MB receive setting) Fiter:All cells all cells(excluding idle cells)up to 16 specified channels Trigger:Specified event specified event occurrence times sequential event(second event after first event) Event:Specified channel,SN abnormality CRC abnormality,specified patternexternal input signal etc. Display:Cell SAR CPCS time stamp Single-channel measurement AAL type automatic evalution and measurement Error additon:Cell loss cell error Measuremnt items: Cell count,CPCS-PDU count assembled timer timeout PDU count frame size countCPI error count SN error count ST error count LI error count about countBE tag error count BA size error count AL error count length error countCRC error count etc(measurement items differ according to AAL type) 1023 channel measurement (live monitor) Detect and measure 1023 channels on line. AAL type automatically detected and measured Measurement items:Cell count CPCS count etc.(measurement items differdingto AAL type) External interface Trigger input(capture event)

仪器保证：

我们的大多数设备在装运之前均经过严格的质量检测与校验。也可申请国家计量证书。